Maytag Maxima front-load washer error codes:
Reference Model: None
These error code explanations can help you diagnose a problem with your Maytag Maxima model front-load washer.
| Code | Meaning | Possible Cause | Possible Parts |
| SUDS | Excessive suds | Excessive suds is detected during the cycle. The cycle goes into a suds kill routine by filling the tube with water and then tumbling the clothes. If this routine doesn't eliminate the suds, the control displays the SUDS code. Use the right amount of high-efficiency (HE) detergent with future loads | HE detergent |
| F0 E1 | Load detected during the washer cleaning cycle | Remove clothes from the washer, the washer must be empty when running a washer cleaning cycle | |
| F1 E1 | Main control board failure | Try to reset the control board by unplugging the washer for 5 minutes and then restoring power. If the F1E1 code returns after restoring power, replace the main electronic control board | Main control board |
| F1 E2 | Motor control board error | Unplug the washer. Check the wire harness connections on the motor control board. Make sure the drive motor connections are secure. If the wiring connections are okay, replace the motor control board | Motor control board |
| F2 E3 | Main control board mismatch or main control board failure | The code appears when you install the wrong main control board. Order and install the correct main control board for your washer. If the code appears when you're not replacing the main control board, then the main control board failed. Replace the main control board | Main control board |
| F3 E1 | Water level pressure switch failure | Unplug the washer. Check the wiring between the water level pressure switch and the main control board. Reconnect any loose wires. Replace the wire harness if damaged. If the wiring is okay, replace the water level pressure switch | Water level pressure switch, wire harness |
| F3 E2 | Temperature sensor failure | Unplug the washer and check the wiring going to the water temperature sensor. If the wiring is okay, replace the temperature sensor | Temperature sensor |
| F4 E0 | Water heater failure | Unplug the washer and check the wiring going to the water-heating element. If the wiring is okay, replace the heating element | Heating element |
| F5 E1 | Door switch failure | This code appears if the control does not detect the door opening after 3 consecutive loads, indicating that the door switch failed. The code also displays when the door switch is open with the door locked. Replace the door lock/switch | Door lock/switch |
| F5 E2 | Door lock failure | The door can't lock. Unplug the washer and check the door lock assembly for damage or a loose wiring connection. Clear any debris out of the door lock assembly. Replace the door/lock switch if defective | Door lock/switch |
| F5 E3 | Door unlock error | The washer won't unlock. Unplug the washer and check the door lock assembly for damage or a loose wiring connection. Replace the door/lock switch if defective | Door lock/switch |
| F6 E1 | Communication error between the main control board and motor control board | Unplug the washer and check the wire harness connections between the main control board and the motor control board. Reconnect any loose wires. Replace the wire harness if damaged. Replace the motor control board if defective. If the problem persists, replace the main control board | Motor control board, main control board, wire harness |
| F6 E2 or F6 E3 | Communication error between the main control board and the user interface control | This code signals a communication failure between the user interface control and the main electronic control board. Unplug the washer and check the wire harness between the user interface control and the main electronic control board. Reconnect any loose wires. Replace the wire harness if damaged. Replace the user interface control. If the problem persists, replace the main electronic control board | User interface control, main control board, wire harness |
| F7 E1 | Motor tachometer failure | Unplug the washer and check the wiring between the motor control board and the drive motor. Check the wire harness connection between the motor control board and the main control board. Reconnect any loose wires. Replace any damaged wire harnesses. If the wiring connections are okay, check to see if the spin basket rotates smoothly. If not, resolve any friction issues in the drive system such as an obstruction caught between the spin basket and tub. If the spin basket rotates smoothly, replace the drive motor. If the problem persists, replace the motor control board | Drive motor, motor control board, wire harness |
| F7 E2 | Motor or motor control board overheated | Overloading the washer can cause this code to appear. Remove some clothes if you overloaded the washer. Friction in the drive system also overheats the motor or the motor control board. Remove any obstructions between the spin basket and the tub. Replace the tub bearing if it's worn or locked up. Replace the drive motor or motor control board if defective | Drive motor, tub bearing, motor control board |
| F8 E0 | Steam valve failure | Check the water supply hoses for kinks. Check for a restricted screen in the water valves. Replace the steam valve if defective | Steam valve |
| F8 E1 | No water detected | Make sure that both water supply valves behind the washer are fully open. In winter, check the fill lines for freezing. Check the drain system for a siphon problem. If the water valve assembly is defective, replace it | Water valve assembly |
| F8 E2 | Dispenser failure | The dispenser can't move into position. Unplug the washer and check the mechanical linkage on the dispenser housing. Repair or replace any damaged dispenser parts | Dispenser assembly parts |
| F8 E3 | Overflow condition | Unplug the washer and, if the washer is overfilled, check the water valve assembly for proper shut-off of water flow. If the water valve assembly is defective, replace it. If the washer is empty when this error code appears, replace the water level pressure switch | Water valve assembly, water level pressure switch |
| F8 E4 | Low water flow | The flow meter detects a long fill time. Make sure that both water supply valves behind the washer are fully open. In winter, check the fill lines for freezing. Check the drain system for a siphon problem. If the water valve assembly is defective, replace it. If water flows normally, replace the flow meter | Water valve assembly, flow meter |
| F9 E1 | Long drain time | Remove excess suds; the washer can't drain excessively sudsy water. Check your house drain system for a clog. Check the drain hose for kinks or clogs. Replace the drain pump if defective. If the washer drains properly, replace the water level pressure switch because it isn't accurately detecting the water level | Drain pump, water level pressure switch |
Maytag Washer Dryer Combo Parts
Related Links
