Kenmore 796. model top-load washer error codes:
Reference Model: None
These error code explanations can help you diagnose a problem with your Kenmore or Kenmore Elite top-load washer with a model number that starts with 796. Kenmore and Kenmore Elite top-load washer error codes appear on the display when the control detects a component problem. Find advice on what to check and which parts you may need to replace when an error code appears by using the chart below.
| Code | Meaning | Possible Cause | Possible Parts |
| IE | Washer fills slowly | Check the water supply faucets behind the washer to make , sure that they are fully open. Check the fill hoses for kinks or freezing (in winter). Check the screens on the water inlet valves for debris or deposits. Replace the water inlet valve assembly if the water inlet screens are clogged | Water inlet valve assembly |
| dE | Lid not closed | If the lid is closed and this message appears when you start the cycle, unplug the washer and check the wire harness connection on the lid lock/switch assembly. If the wiring connections are sound, the lid lock/switch assembly usually needs to be replaced | Lid lock/switch assembly |
| dL | Lid lock failure | Check for debris in the lid lock assembly that could prevent the lock mechanism from engaging. Unplug the washer and check the wiring connections on the lid lock/switch assembly. If you find no wiring problems, you usually need to replace the door lock/switch assembly | Lid lock/switch assembly |
| FE | Water level too high | The washer is usually fills continuously because a water valve failed when this code appears. Unplug the washer and shut off the water supply. The water inlet valve assembly usually needs to be replaced to fix this problem | Water inlet valve assembly |
| E6 | Clutch error | The control detects a problem with the clutch motor. Unplug the washer. Check the wiring harness connections between the main electronic control board and the clutch motor. If the wiring connections are sound, the clutch motor or the main electronic control board usually needs to be replaced | Clutch motor, Main electronic control board |
| uE | Load is out of balance or too small | If a small load is in the washer, add a few towels or garments to the load. If the load is a normal size, then redistribute the load and see if the washer spins. If the washer tub moves and bangs violently during the spin cycle, one or more of the suspension rod/spring assemblies may need to be replaced. Unplug the washer and examine those components | Suspension rod/spring assembly |
| UE | Load is out of balance or too small | If a small load is in the washer, add a few towels or garments to the load. If the load is a normal size, then redistribute the load and see if the washer spins. If the washer tub moves and bangs violently during the spin cycle, one or more of the suspension rod/spring assemblies may need to be replaced. Unplug the washer and examine those components | Suspension rod/spring assembly |
| tE | Thermistor error | Unplug the washer and check the wiring between the control board and the thermistor (temperature sensor). If the wiring is sound, measure the resistance of the thermistor. It should read between 80,000 to 90,000 ohms) at room temperature. If the thermistor is defective, replace it. If resistance of the thermistor is normal through the circuit, replace the main electronic control board | Thermistor, Main electronic control board |
| PE | Water level sensor failure | Unplug the washer and check the wire harness connections between the water level sensor and the electronic control board. Reconnect any loose wires or replace the wire harness if damaged. If the wire connections are okay, replace the water level sensor | Water level sensor, wire harness |
| LE | Drive motor thermal overload tripped | A failed drive motor or a restriction in the drive system of the washer causes this code. Unplug the washer. See if the basket spins freely. If not, examine and repair the cause of the restriction in the drive system. If the basket spins freely, check the wiring connections between the drive motor and the control board. Check the resistance through the drive motor windings. The winding should measure between 5 and 15 ohms. If the motor is defective, replace it | Drive motor, Drive system components |
Related Links
